מתג לטלפוני IP עם 24 פורט על בסיס תשתית קיימת
מתג (Switch) לקישור 24 טלפוני IP על תשתית הטלפון הישנה - ללא צורך בהחלפת התשתית

מתג 24 PoLRE
החלטתם לרכוש מרכזיית IP ולעשות שימוש בטלפוני IP. מתגי ה- PoLRE מאפשרים לכם לעשות שימוש בתשתית הטלפוניה הקיימת גם עם מערכת הטלפוניה החדשה תוך שמירה על הפרדת הרשתות ורמת אמינות גבוהה ושימור על ההשקעה לאורך שנים.
מתגי ה PoLRE מאפשרים לשמר את ההשקעות בתשתית תוך שימוש בפתרונות תקשורת המשולבים בחזית הטכנולוגיה - State-of-the-art.
מתגי ה PoLRE מאפשרים לכם מעבר מהיר לטכנולגיית IP וללא פשרות על איכות, אבטחה וחיסכון של עד 70% בעלות לאורך היישום.
מתגי ה PoLRE מאפשרים לכם החזר השקעה ROI בזכות עלויות האחזקה הנמוכות והשיפור ביעילות התקשורת.
חשוב לציין שמתגי ה- PoLRE תואמים לכל יצרני מרכזיות ה- IP ועובדים בסטנדרטים התואמים לכל ספקי התקשורת המספקים שירותי VoIP (טלפוניית אינטרנט).
פתרון זה זכה להכרה בינלאומית ומוגן בפטנטים - חיסכון מובטח !
הפתרון נמכר באמצעות מפיצים מאושרים שעברו הסמכה.
פנו אלינו למפיץ הקרוב אליכם.
אנו מגייסים מפיצים חדשים לפתרון - אנא צרו עמנו קשר לתאום פגישה 0544558591
פנו אלינו לייעוץ חינם: 072-270-2430
מפרט טכני
PoLRE PL-024/PL-048 leverages telephone cabling infrastructure to create a parallel network with Power-over-Ethernet. This is a plug-and-play solution that can be deployed quickly and easily with the default configuration.
PoLRE
Physical
Models:
-
1U - 1.75" x 17.13 " x 9.92" (H x W x D) (4.45 x 43.5 x 25.2 cm)
Mounting:
-
Standalone or rack or shelf-mountable
-
2 brackets included for installation
Processor:
-
Broadcom BCM56018 switch processor, 266MHz
Memory:
-
32MB FLASH, 64MB DDR SDRAM
Fans:
-
2 on chassis, 2 on power supply unit
Environmental
Relative Humidity:
-
10% to 95% (non-condensing) at 35°C
Power
Power supply:
-
Autosensing 100-240VAC, 50/60 Hz.
-
Hot-Swappable Power Supply Unit
-
Power output: 500W max at 100VAC, 1000W max at 240VAC
Consumption:
-
Model PL-024: 16.5W
-
Model PL-048: 22W
Power injection (PoE):
-
DC voltage: -54VDC
-
Endpoint devices must be compliant with IEEE 802.3af
PowerWise power/load sharing:
-
2 male connectors (rear), DC IN and DC OUT: -52VDC
Interface
Interface: Ethernet uplink(Trunk IP)
Maximum 2 uplinks, each 1Gb/s (full duplex), either:
-
2 mini-GBIC ports: 1000 Base-TX/SX/LX/EX/ZX/LHX (determined by SFP, transceiver module installed), Ethernet IEEE 802.3z, fiber optic cable, or
-
2 RJ45 ports: 10/100/1000 Base-T autosensing, independent speed selection, Ethernet IEEE 802.3, CAT5e copper cable
Interface: Downlink (PoE and IP to PhyLink)
-
Model PL-024: 1 RJ21 male telco connector (standard), 24 pairs used.
-
Model PL-048: 2 RJ21 male telco connectors (standard), 48 pairs used.
-
Maximum distance: 1200' (365.76m) CAT3 UTP cable, 24 AWG.
-
Speed: 10Mb/s (full duplex)
-
PoE power: 10 Watts.
POE:
The PhyLink functions as a PSE, providing up to 10W POE to IEEE 802.3af compliant IP Phones.
Management Interface:
-
In-band management: provide all system OAM&P functions: software updates, configurations import/export, and management system interaction through Ethernet trunk port.
-
Out-of-band management: provide management interfaces through a 100 Base-T auto-sensing Ethernet Interface.
-
Serial Management: provides command line interface(CLI) with serial settings 115200/8/n/1 using RJ45 to DB9 cable (included in box)
OAM&P:
-
Configuration Management
-
Performance Management
-
Fault Management
-
Status Monitoring
Ethernet/IP Functionality
General Bridging Function:
-
Support IPv4 packet
-
Support IEEE802.1d Ethernet bridge function between trunk Ether ports.
-
Support Rapid Spanning Tree Protocol (RSTP) for the trunk interfaces per IEEE 802.1w
VLAN:
-
Support IEEE 802.1q Port-based VLAN and Protocol-based VLAN
-
Support 512 non-stacked VLAN-ID simultaneously ranging from 1 to 4095
-
Support VLAN stacking and VLAN cross-connect
-
Support static VLAN group and membership provisioning
PhyLink
Physical
Dimensions:
-
1.8cm x 2.8cm x 6.5cm (HxWxD); 0.71” x 1.1” x 2.56” (HxWxD)
Mounting:
-
Inline between the CAT5 cable (to IP endpoint) and the CAT3 cable (to RJ11 jack)
Interface
Interface PoLRE Switch side:
-
1 RJ11 port: CAT3 unshielded single twisted pair cable. Between the wall plate and adapter, you can reuse the existing silver satin when doing a DNIC/POTS displacement.
Interface Ethernet side: for IP end point device:
-
1 RJ45 port: 10/100 Base-T autosensing, IEEE 802.3af, 10 Mb connection to IP end device
Power
Power injection (PoE):
DC voltage on RJ45 port:
-
54v max
-
37V when 1200' (365.76m) away from its PoLRE Switch Powers Class 1, Class 2 and some Class 3 IEEE 802.3af compliant IP devices
Environmental
Humidity:
-
10% to 95% (non-condensing) at 35° C